- 您现在的位置：买卖IC网 > Sheet目录1204 > CT0805S14BAUTOG (EPCOS Inc)VARISTOR 14VRMS 0805 SMD AUTO
Multilayer varistors (MLVs)
Automotive series
7.5
Adhesive application
Thin or insufficient adhesive causes chips to loosen or become disconnected during curing.
Low viscosity of the adhesive causes chips to slip after mounting. It is advised to consult the
manufacturer of the adhesive on proper usage and amounts of adhesive to use.
7.6
Selection of flux
Used flux should have less than or equal to 0.1 wt % of halogenated content, since flux residue
after soldering could lead to corrosion of the termination and/or increased leakage current on the
surface of the component. Strong acidic flux must not be used. The amount of flux applied should
be carefully controlled, since an excess may generate flux gas, which in turn is detrimental to sol-
derability.
7.7
Storage of CTVSs
Solderability is guaranteed for one year from date of delivery for multilayer varistors, CeraDiodes
and ESD/EMI filters (half a year for chips with AgPd and AgPt terminations) and two years for
SHCV and CU components, provided that components are stored in their original packages.
Storage temperature:
Relative humidity:
25 ° C to +45 ° C
≤ 75% annual average, ≤ 95% on 30 days a year
The solderability of the external electrodes may deteriorate if SMDs and leaded components are
stored where they are exposed to high humidity, dust or harmful gas (hydrogen chloride, sulfurous
acid gas or hydrogen sulfide).
Do not store SMDs and leaded components where they are exposed to heat or direct sunlight.
Otherwise the packing material may be deformed or SMDs/ leaded components may stick togeth-
er, causing problems during mounting.
After opening the factory seals, such as polyvinyl-sealed packages, it is recommended to use the
SMDs or leaded components as soon as possible.
7.8
Placement of components on circuit board
Especially in the case of dual-wave soldering, it is of advantage to place the components on the
board before soldering in that way that their two terminals do not enter the solder bath at different
times.
Ideally, both terminals should be wetted simultaneously.
7.9
Soldering cautions
An excessively long soldering time or high soldering temperature results in leaching of the outer
electrodes, causing poor adhesion and a change of electrical properties of the varistor due to
the loss of contact between electrodes and termination.
Wave soldering must not be applied for MLVs designated for reflow soldering only.
Keep the recommended down-cooling rate.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 65 of 72
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
CT1206K17G
VARISTOR 17VRMS 1206 SMD
CTB-B-B-15
CIRCUIT BREAKER ROCKER 15A SP BK
CU3225K17AUTOG2
VARISTOR AUTO 17VRMS 3225 SMD
CU3225K250G2K1
VARISTOR STD 250VRMS 3225 SMD
CV10-RP-M-0
CONN JACK STR COAXIAL SMD
CVM50XM
MEMBER MOD PIC12C508/PIC12C509
CVM67XM
MEMBER MODULE PIC12C671/672
CVM77XM
MEMBER MODULE PIC16C773/774
相关代理商/技术参数
CT0805S17GK2
制造商:EPCOS 制造商全称:EPCOS 功能描述:Ceramic transient voltage suppressors
CT0805S20ACC2G2
制造商:EPCOS 制造商全称:EPCOS 功能描述:Ceramic transient voltage suppressors
CT080A
制造商:ESSENTRA COMPONENTS 功能描述:CABLE TIE STANDARD:NYL NATURAL 制造商:Richco 功能描述:CABLE TIE STANDARD:NYL NATURAL
CT080B
制造商:ESSENTRA COMPONENTS 功能描述:CABLE TIE STANDARD:NYL BLACK 制造商:Richco 功能描述:CABLE TIE STANDARD:NYL BLACK
CT08-1200
功能描述:电流变压器 Current Sense Transformer
RoHS:否 制造商:EPCOS 安装风格: 电感:320 uH 电流额定值: 匝数比: 次级线圈电阻:1140 mOhms 端接类型:SMD/SMT 长度:8.13 mm 宽度:7.11 mm 高度:5.08 mm 频率:
CT081A
制造商:Richco 功能描述:CABLE TIE STANDARD:NYL NATURAL
CT081B
制造商:ESSENTRA COMPONENTS 功能描述:CABLE TIE STANDARD:NYL BLACK 制造商:Richco 功能描述:CABLE TIE STANDARD:NYL BLACK
CT082A
制造商:ESSENTRA COMPONENTS 功能描述:CABLE TIE STANDARD:NYL NATURAL 制造商:Richco 功能描述:CABLE TIE STANDARD:NYL NATURAL